Search Results

Search Again
Page 1 of 2
  1. sstepane
    Post

    Wismec SINUOUS RAVAGE230 dying

    Just from the symptoms - replace the fire button.
    Post by: sstepane, Nov 5, 2019 in forum: Discussions
  2. sstepane
    Post

    Spontaneous combustion

    Hi, Wrong reason to put development on hold. Many devices suffer from this issue, many oif them are from jwel, take a couple month old Ikoon for...
    Post by: sstepane, Oct 22, 2019 in forum: Info & Guides & Reviews
  3. sstepane
    Post

    predator 228 dead? black screen no buttons work.

    252x = XC6202 series LDO
    Post by: sstepane, Oct 19, 2018 in forum: Issues
  4. sstepane
    Post

    rx300 проблема с 4ртым аккумулятором

    Привет, Тщательно, желательно спиртом, протереть контакты аккумуляторов и балансиров, контакты самих аккумуляторов, поменять их местами, надежно...
    Post by: sstepane, Mar 20, 2018 in forum: Русскоязычный форум
  5. sstepane
    Post

    predator 228 dead? black screen no buttons work.

    Hi, Check if bottom screws are tightened. Check if mod works without display (assume display just doesn't work). Check with microscope all of...
    Post by: sstepane, Mar 19, 2018 in forum: Issues
  6. sstepane
    Post

    Wismec Gen3 Bricked

    Hi, I'm repairing another mod with the same problem - it keeps losing firmware. Had to change its microcontroller. It's likely a problem with...
    Post by: sstepane, Feb 26, 2018 in forum: Issues
  7. sstepane
    Post

    Wrong Resistance on Primo 2.0

    Resoldering ground wire could help if there would be one. Connector is hot-pressed in the case and the case acts as a ground wire. Adding ground...
    Post by: sstepane, Feb 22, 2018 in forum: Issues
  8. sstepane
    Post

    Low Voltage Setting

    I think it's a bit more complicated. Depending on current the drop may go up to 2.5-2.0 volts and for some batteries this is OK. So, as far as I...
    Post by: sstepane, Feb 13, 2018 in forum: Suggestions
  9. sstepane
    Post

    TC accuracy vs mod efficiency

    Hi, I did some "dirty" quick test some month ago, but not for TC mode - for power. Here are some results (it was made using Joyetech Cuboid...
    Post by: sstepane, Feb 7, 2018 in forum: Discussions
  10. sstepane
    Post

    Подключение к ПК

    Я бы порекомендовал попробовать локализовать возможную неисправность.
    Post by: sstepane, Feb 2, 2018 in forum: Русскоязычный форум
  11. sstepane
    Post

    Подключение к ПК

    Как пишут на некоторых форумах в таких случаях: Продолжайте наблюдения.
    Post by: sstepane, Feb 2, 2018 in forum: Русскоязычный форум
  12. sstepane
    Post

    Battery volt drop during puff

    Hi, VTC5, for example, has almost constant drop of 0.4 volts at 20A load along all of its discharge line down to 2.5 volts. 70 watts approximately...
    Post by: sstepane, Jan 17, 2018 in forum: Discussions
  13. sstepane
    Post

    Сгорел RX200 после перепрошивки на ArcticFox 171228

    Ну я не раз видел просто треснувшие конденсаторы, которые при этом были коротко-замкнутые. Ну и, естественно, раз он ушел в КЗ - при следующем...
    Post by: sstepane, Jan 14, 2018 in forum: Русскоязычный форум
  14. sstepane
    Post

    Сгорел RX200 после перепрошивки на ArcticFox 171228

    Так в любом случае, фильтрующий конденсатор сжечь прошивкой невозможно. И без него работать будет, но могу проявляться мелкие глюки. Кроме того,...
    Post by: sstepane, Jan 14, 2018 in forum: Русскоязычный форум
  15. sstepane
    Post

    Сгорел RX200 после перепрошивки на ArcticFox 171228

    В таком ракурсе рассмотреть не могу, но вижу молекулярный клей (его там быть не должно) и то, что основной контакт батареи "+" паялся, да и плата...
    Post by: sstepane, Jan 14, 2018 in forum: Русскоязычный форум
  16. sstepane
    Post

    Сгорел RX200 после перепрошивки на ArcticFox 171228

    Совпадение и это не резистор, а конденсатор (можно заменить на что-то типа 100 мКф, 10+ вольт). За много ремонтов рх-ов никогда не видел, чтобы...
    Post by: sstepane, Jan 14, 2018 in forum: Русскоязычный форум
  17. sstepane
    Post

    Wismec Sinuous P80 Restarting

    So it seems firmware issue after all.
    Post by: sstepane, Jan 11, 2018 in forum: Issues
  18. sstepane
    Post

    Wismec Sinuous P80 Restarting

    Clean battery contacts with rubber or something like. Try different batteries with different power settings (5 - 10 - 30 Watt).
    Post by: sstepane, Jan 11, 2018 in forum: Issues
  19. sstepane
    Post

    Wismec Sinuous P80 Restarting

    So it's seems to be OK then. Reverse-nothing means that some semi-conductor is in chain.
    Post by: sstepane, Jan 11, 2018 in forum: Issues
  20. sstepane
    Post

    Wismec Sinuous P80 Restarting

    I don't recall the construction of this particular device, but in 95% in my experience - the connector is the last place that faults. But clean it...
    Post by: sstepane, Jan 11, 2018 in forum: Issues
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2