ArcticFox 170803

Discussion in 'Archive' started by maelstrom2001, Aug 4, 2017.

Thread Status:
Not open for further replies.
  1. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,067
    Likes Received:
    986

    English:

    default display orientation for RX GEN3;
    dual battery configuration support for RX200.
    Russian:

    ориентация дисплея по умолчанию для RX GEN3;
    поддержка двухбатарейной конфигурации для RX200.
     
    Zotez, Vaper, Scaldyballs and 2 others like this.
  2. Reky_FR

    Reky_FR New Member

    Joined:
    Aug 4, 2017
    Messages:
    7
    Likes Received:
    1
    Edit : See last post below, Safe mode method has fixed the issue

    I don't know if my made a mistake or missed any usefull information but my VaporFlask Lite is bricked
    I've used the last NToolbox 170624 with this arctifox firmware to flash the firmware (previous one was 170603) and during the flash, an error message appears "firmware update is failed"

    Now i can not start the box anymore and and it's not detected by the computer: "waiting for device"

    Any help would be highly appreciated!
    Thanks
     
    #2 Reky_FR, Aug 4, 2017
    Last edited: Aug 4, 2017
  3. dil3mm4

    dil3mm4 Active Member

    Joined:
    May 22, 2017
    Messages:
    165
    Likes Received:
    50
    This kind of message generates panic.
    Did you tried to flash in safe mode after the fail?
     
  4. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,067
    Likes Received:
    986
    Anddrepjksm, Vavun and dil3mm4 like this.
  5. dil3mm4

    dil3mm4 Active Member

    Joined:
    May 22, 2017
    Messages:
    165
    Likes Received:
    50
    @maelstrom2001 are new features ready to pop out in next releases? :p
     
  6. Reky_FR

    Reky_FR New Member

    Joined:
    Aug 4, 2017
    Messages:
    7
    Likes Received:
    1
  7. Ku6ep

    Ku6ep New Member

    Joined:
    Aug 4, 2017
    Messages:
    4
    Likes Received:
    0
    After installation I can't connect to my device via NFE Tools, get message about old software and needed to get last version. Firmware, live info work good, only setting editor not work.
     
  8. ReikoKitsune

    ReikoKitsune Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    643
    Likes Received:
    526
    @Ku6ep because this is a nightly build and you should use nightly build of the NToolbox.
     
  9. Ku6ep

    Ku6ep New Member

    Joined:
    Aug 4, 2017
    Messages:
    4
    Likes Received:
    0
    Understood :) Where is it?
     
  10. BoORDeL

    BoORDeL New Member

    Joined:
    May 20, 2017
    Messages:
    5
    Likes Received:
    1
    the same page where you clicked for this fw... just scroll down
     
    Ku6ep likes this.
  11. invisiblehand13

    invisiblehand13 New Member

    Joined:
    May 17, 2017
    Messages:
    5
    Likes Received:
    1
    mmmmmmm....updates...me like updates....ME LOVE UPDATES!!! You guys are awesome by the way @maelstrom2001 and @ReikoKitsune and everyone else involved
     
    Vaper likes this.
  12. jahan79

    jahan79 New Member

    Joined:
    Aug 5, 2017
    Messages:
    2
    Likes Received:
    0
    How do I use dual battery mode in rx200? I dont see the option to enable it. 2 batteries do not work in any orientation.
     
  13. MaxTheSpy

    MaxTheSpy New Member

    Joined:
    Aug 5, 2017
    Messages:
    23
    Likes Received:
    10
    Is there a way to change the board temp from C to F yet? I havent seen it in the settings anywhere or in the editor. Would be helpful
     
  14. ReikoKitsune

    ReikoKitsune Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    643
    Likes Received:
    526
    Board temperature unit depends on temperature unit in the profile.
    If you are using TC, just set units to F and board temperature will be automatically measured in F.
    If you are using VW - all same, but first you need to select any TC material, change temperature and then return back to VW.

    Turn on your brain... The electrical circuit is not closed.
     
  15. MaxTheSpy

    MaxTheSpy New Member

    Joined:
    Aug 5, 2017
    Messages:
    23
    Likes Received:
    10
    You are awesome thank you! Is there a board temp I should keep it under? just o I know it wont self destruct or anything
     
  16. ReikoKitsune

    ReikoKitsune Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    643
    Likes Received:
    526
    No need to think about it, firmware have temperature protection. If temperature will be higher than 75C firmware won't let you to vape and will show appropriate message.
     
  17. jahan79

    jahan79 New Member

    Joined:
    Aug 5, 2017
    Messages:
    2
    Likes Received:
    0
    Anyone know where I can find an 18650 sized bridge? Or instructions on how to make one.
     
  18. Highlife

    Highlife New Member

    Joined:
    Aug 2, 2017
    Messages:
    1
    Likes Received:
    0
    Hi
    Is there any reason to run a rx200 on 2 batteries? This device is not built to do so! If you want do to it anyways you have to find out youself. Vape safe and don`t start any experiments which could go wrong.
    [Edit]: You could get yourself another 18650 battery. This would solve the problem.
     
  19. Gedeon

    Gedeon Member

    Joined:
    Jun 8, 2017
    Messages:
    72
    Likes Received:
    35
    This way you can insert a bottle instead of the battery and make a squonking device.
     
    slavyk likes this.
  20. Vavun

    Vavun New Member

    Joined:
    Aug 6, 2017
    Messages:
    27
    Likes Received:
    11
    Hi everyone and sorry for bad english =(

    1) Is it possible to enable battery indicator in dual mode like in default firmware for eVic Primo ? (two batteries instead of one battery indicator)
    2) Is it planned (Is it possible at all?) to add a kind of protectoin while it is charging ?
    I mean in some boxmods while you try to vape while it charging the charging is turned off and turned on again when you stop pushing fire button.
    3) How can I change (if it possible) display blackout timeout ?

    joyetech evic primo 2.0
    FIrmware - af_170803.bin
    Thanks =)
     
Thread Status:
Not open for further replies.