Wismec EXO Skeleton ES300 Support

Discussion in 'Suggestions' started by Janishewskiy, Apr 23, 2018.

  1. Janishewskiy

    Janishewskiy Active Member

    Joined:
    May 17, 2017
    Messages:
    142
    Likes Received:
    27
    Is it possible to support Wismec EXO Skeleton ES300?
    The firmware is available on the Wismec website.

    It is worth doing this, firstly, for the kit, there is a problem with the screen, but if the same as in the tube, then there should not be any problems.

    Secondly, there is a device: MyVapors myTri Kit, defined as Skeleton.
    This is a very cheap device, at Vape Sourcing now $ 20
     
    spado and Greithoth214 like this.
  2. Greithoth214

    Greithoth214 New Member

    Joined:
    Aug 16, 2018
    Messages:
    4
    Likes Received:
    0
    Necro thread but I absolutely support this! :D
     
  3. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Sh*t, I was so hoped that it was forgotten :D
     
  4. Janishewskiy

    Janishewskiy Active Member

    Joined:
    May 17, 2017
    Messages:
    142
    Likes Received:
    27
    I was told that Wismec immediately removed it from production.
    Burned. Categorically can not be turned on after purchase, immediately flashing with a new firmware.
    Batteries in the device can not be charged either. Dangerous.

    Maybe, in the version MyVapors myTri finished, but not fact.
     
  5. spado

    spado Member

    Joined:
    May 18, 2017
    Messages:
    50
    Likes Received:
    13
    #5 spado, Nov 26, 2018
    Last edited: Nov 26, 2018
    Greithoth214 likes this.
  6. Greithoth214

    Greithoth214 New Member

    Joined:
    Aug 16, 2018
    Messages:
    4
    Likes Received:
    0
    The good news (I hope) is, it appears to only use the ES300's battery door assembly. I downloaded ES300 firmware to check and it is NOT a match. It's not compatible with AF either but I figured it was worth a look in case it maybe used an Eleaf Tria's internals.
     
  7. spado

    spado Member

    Joined:
    May 18, 2017
    Messages:
    50
    Likes Received:
    13
    Wait... a match with what? I couldn't find software upgrades for the myTri and provided it says ES300 in the bottom door, it can work with either 2 or 3 cells and has the same screen on the top you could assume it probably is just a different enclosure for the same board as the Skeleton.
     
  8. Greithoth214

    Greithoth214 New Member

    Joined:
    Aug 16, 2018
    Messages:
    4
    Likes Received:
    0
    The MyTri does NOT recognize as an ES300 on any of my checking anyhow. I was honestly wondering if they used the eLeaf Tria but that also was a no. I'm lost as to what they've done for firmware. Mine will only work with all three batteries in as well.
     
  9. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    Sorry for up the thread.....and my bad english!!

    Any chance to put AF in myVapors/myTri?

    Tested for months mine is equipped with 3xSamsung INR18650-25R.
    Also tested the charge with USB port and it appear stable.
    It's my first device at home!!

    I typically use it at 35/50 Watt but brand firmware is terrible.
    Obscenous pre-heat function, battery management and poor function.

    I think force PID and make compatibility with Joyetech Elitar Pipe is not a good idea for the difference performance of devices and i don't know it is possible.

    I hope in second life for this box.

    And many thanks for your great work!!
    ;)
     
  10. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Hello!
    Can you provide its original firmware please? Or it is detected as [W084], the same as Wismec Skeleton? And which version is installed? To see it, turn the device off by 5 clicks and then press Fire button 20 times (standard JWEI action).
    And one more question: does it starts with 2 batteries? As far as I know, in recent 1.04 version 2 batteries mode is disabled for safety reasons, but on the Wismec website I see 1.03 only.
    Yep, it is not a good idea at all, do not do that :)
     
  11. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    Hi.....

    I have serched but not found original firmware....
    Any way to back-up the installed software?

    Is detected as [J084] and firmware installed is 1.04.

    I have not tested with 2 battery, useless in my opinion.
    Also not tested the power bank mode.

    Thanks for your interest!!

    :)
     
  12. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Unfortunately not.
    The only thing I can offer before we can go further is to try to flash Wismec firmware 1.03 and test it. We can add support based on this firmware only, but there is no guarantees at all that 1.03 will work properly on your device.
    Or try to ask 1.04 firmware directly from MyVapors, it is longer but safer way.

    P. S. strange, but can not find 2 batteries support in Wismec 1.03 firmware. Did they turn it off too? Hmm :confused: if so, MyVapors 1.04 should be the same as Wismec 1.03 o_O
    https://www.fasttech.com/forums/7765100/t/2940932/firmware-1-03-disables-option-for-2-cells
     
    #12 maelstrom2001, Jun 17, 2019
    Last edited: Jun 17, 2019
  13. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    Uh....

    Wismec update software doesn't recognize the box....
    It return:
    Device Name: unknown device
    No firmware or hardware version

    NToolbox Firmware updater module show Hardware v1.00

    Other way to put 1.03 Wismec firmware??
     
  14. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Ermm, another surprise, OK. It seems that Wismec updater looking for device with W084, but you wrote earlier, MyTri have
    Well, if you want to take a risk, there is a way. Open NToolbox Firmware Updater and hold Ctrl+Alt while selecting firmware .bin file: this will disable PID check and force update with Wismec firmware.
    Before flashing I suggest to check ability to start the box in Safe Mode, and strongly recommend flash firmware without batteries installed.
    P. S. also please check PID in Safe Mode and at normal boot: they are may be different.
     
  15. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    GREAT!!

    All done.....thank you for instruction!!

    Wismec firmware has activated the stripes led that blink under the case (no way, de-activated through new voice in menu) and the splash screen show EXO Skel. during turn on/off the box.

    Thanks for support.......next step??

    Edit:

    I switched Safe mode through Advanced tab function with "exception occurred, operation failed early" message but it right worked!!
     
    #15 Venessia, Jun 17, 2019
    Last edited: Jun 17, 2019
    maelstrom2001 likes this.
  16. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Please check PID in normal and Safe Mode, it would be nice to attach 2 screenshots of NToolbox Firmware Updater: with 1.03 firmware version detected (in normal mode) and 0.00 firmware version (Safe Mode activated).
    Try to enter Safe Mode with "+" button hold while connecting to PC without batteries, as it described in Products Manual. Or it may be "-" button instead of "+". It would be nice to check that you can enter Safe Mode not with Firmware Updater only, but with button as well.
    And then our turn :D
     
    #16 maelstrom2001, Jun 17, 2019
    Last edited: Jun 17, 2019
  17. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    maelstrom2001 likes this.
  18. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Great news, thank you! Tomorrow will add support and upload test build :)
     
    Venessia likes this.
  19. Venessia

    Venessia New Member

    Joined:
    May 17, 2017
    Messages:
    13
    Likes Received:
    8
    Many thanks for your great work!!
     
    maelstrom2001 likes this.
  20. maelstrom2001

    maelstrom2001 Developer
    NFE Team

    Joined:
    May 4, 2017
    Messages:
    1,175
    Likes Received:
    1,073
    Really don't know if will that work properly, or will burn the box. As always, no guarantees, at your onw risk [​IMG]
     

    Attached Files:

    Venessia likes this.